Facebook

PH-6000 Selection & Sizing Hub

Vegetable Washing Machine

PH-6000 Selection & Sizing Hub

The PH-6000 is an air-bubble washer rated at 2000 kg/h and built in SUS304 stainless steel, and this hub turns its datasheet into the decisions a plant actually has to make. Start by matching your hourly washed output to a vegetable washing machine, then check the 6000×800×1300 mm envelope, the 380V/1.5 kW supply and the water and drainage points that a fruit and vegetable washing machine needs before it lands on your floor. Each module below ends with the fact to confirm and the detail to send with your layout.

Vegetable Washing Machine
Capacity 2000 kg/h
Overall size 6000×800×1300 mm
Power 380V / 1.5 kW
Net weight 500 kg
Material SUS304
Min. order 1 set

Sizing Throughput: 2000 kg/h in Real Line Terms

The datasheet figure is 2000 kg/h on a 380V, 1.5 kW supply. Treat that as the ceiling you plan against, not as a guaranteed washed output for every crop: leafy greens, bean sprouts and cut salad carry very different soil loads and need different contact time with the bubble and spray action. The sizing question is therefore how many units your target rate needs, not whether one number is “enough”.

InfeedYour target kg/h
Bubbling + surfingLift and separate soil
Spray + water impactRinse and desalt
OutfeedTo sorting or packing

Illustrative planning example

A fresh-cut facility targets 1,400 kg/h of washed leaf. Allowing roughly 70% of the 2000 kg/h rating for changeovers, cleaning windows and difficult soil loads, one PH-6000 covers the target with headroom. A facility targeting around 3,200 kg/h would instead be looking at two units running in parallel, or a single line arrangement sized up — capacity customization is offered according to production needs, so the standard rating is a reference point rather than a fixed limit.

These are planning figures for a conversation, not a performance commitment. Final throughput depends on your produce, water temperature and how long the product stays in the wash zone.

One unit is usually enough when

Your target sits comfortably under 2000 kg/h for the shift pattern you run, and the produce is a single family — all leaf, or all sprouts — rather than a mixed daily changeover.

Plan parallel or inline when

Your target exceeds the rating, or upstream sorting delivers in batches that would otherwise idle a single 6000 mm machine body between runs.

Validate before you sign

Produce list and soil load, infeed rate from the grading line, required soak and spray contact time, and where the dewatering or packing stage picks the product up.

PH-6000 vegetable washing machine body with SUS304 wash tank
The PH-6000 body measures 6000×800×1300 mm and weighs 500 kg net — plan the aisle before you plan the order.

Footprint & Layout Envelope

A 6000 mm long machine does not fit into a 6000 mm gap. The published envelope is the machine body only; working clearance for infeed transfer, outfeed transfer, cleaning access and drainage falls all sit outside it, and those are the numbers your layout drawing has to show.

  • Machine envelope: 6000 mm length × 800 mm width × 1300 mm height — confirm the route in (doors, lifts, aisle turns) handles a 6 m body.
  • Infeed and outfeed clearance: leave working space at both ends for transfer from grading and onto dewatering or packing.
  • Conveyor integration: the machine is designed to integrate with existing processing lines, and the product page notes that linking it to sorting and packaging conveyors can optimize throughput and reduce manual intervention.
  • Floor loading: 500 kg net weight spread across the 6000×800 mm footprint — check slab condition and any point loads at the tank feet.
  • Drainage position: the wash zone needs a fall and an outlet under or beside the machine; decide the position before the layout is frozen.
  • Maintenance access: the build is described as easy to clean and maintain, so keep one long side reachable for the routine you plan to run.

Build & Hygiene Specification

The frame and tank are built in food-grade SUS304 stainless steel, described on the product page as corrosion- and wear-resistant. For a wash line that sees water, soil and mild detergents every shift, that material choice is a maintenance decision as much as a hygiene one.

SUS304 construction

Corrosion- and wear-resistant stainless steel across the modular layout, selected for durability and food-safety compliance.

Three-action wash

Bubbling, surfing and spray washing work together, driven by a high-pressure fan and a water-impact system.

Soak, clean, desalt

The machine is built to deliver soaking, cleaning and desalting effects in one pass rather than as separate stations.

Delicate-produce handling

The page states the process removes dirt and residues without damaging delicate produce in packaging-plant use.

Easy cleaning and maintenance

Accessibility is designed in to help minimise downtime between shifts and between product changeovers.

Controlled protocol

Controlled cleaning protocols are described as supporting preservation of texture and freshness through the wash stage.

Vegetable Washing Machine
SUS304 stainless steel body and wash tank, built for wet, food-contact duty.

Utility & Installation Readiness

Only one utility is published to the digit — the electrical supply. Everything else in this table is a point to confirm with your own engineering team and with us before the machine is shipped, because a washer that arrives without a drain position is a washer that waits.

Utility Published value Confirm before ordering
Electrical supply 380V, 1.5 kW Plant voltage and frequency, isolator and starter arrangement, cable route to the final machine position
Wash water Spray washing and high-pressure water impact are part of the wash action Connection size, available pressure and flow at the machine position
Drainage Not published Outlet position, fall and capacity for continuous spray operation
Air movement High-pressure fan built into the machine Ventilation and clearance around the fan and motor
Floor loading N.W. 500 kg on a 6000×800 mm footprint Slab condition and support at the tank feet
Commissioning support Installation guidance and remote support offered Who is on site at commissioning and how the remote session is arranged
PH-6000 utility and installation checklist machine view
The machine runs on 380V / 1.5 kW; water, drainage and access clearances are site items to settle before delivery.

Match the Scenario to the Specification

The product page names the settings this washer is built for. Read each one as a decision: what the machine brings, and what you have to lock down on your side before it is the right answer.

Salad processing line

Fresh-cut and salad lines

The page lists salad processing lines among the intended settings, with bubbling, surfing and spray washing working on delicate leaf rather than against it.

Decision to lockContact time in the wash zone for your leaf thickness and soil load, and where the salad goes straight after outfeed.

Bean sprouts

Bean sprout operations

Bean sprouts are named on the page as a produce type the air-bubble action cleans more thoroughly, using bubbling, surfing and cleaning spray together.

Decision to lockYour peak hourly rate against the 2000 kg/h rating, and the split between washing time and dewatering time downstream.

Packing facility

Vegetable packaging facilities

The machine is described for packaging-plant use where dirt and residues must come off without damaging delicate produce, and the page notes that linking to sorting and packaging conveyors can optimize throughput and reduce manual intervention.

Decision to lockConveyor heights at both ends and the transfer points, so the 1300 mm working height of the body lines up with your packing bench.

Ready-to-eat meals

Ready-to-eat meal production

The page lists ready-to-eat meal production as an intended application, with soaking and desalting built into the same pass as the wash.

Decision to lockWater supply and drainage sized for continuous spray operation, since a ready-to-eat line rarely stops mid-shift.

Configuration Comparison: Single Unit, Custom Capacity, Full Line

Three honest options rather than three invented columns. Only the PH-6000 figures below are published specifications; the other routes are framed by what you would need to confirm with the team.

Option What is defined Choose it when What to confirm
PH-6000 air-bubble washer 2000 kg/h capacity, 6000×800×1300 mm, 380V / 1.5 kW, 500 kg net, SUS304, MOQ 1 set Your washed-output target sits inside the 2000 kg/h rating and the floor can take a 6 m machine body plus working clearance Produce mix, infeed rate, drain position and floor loading
PH-6000 with customized capacity Capacity customization is offered according to production needs; the standard datasheet figures then become the reference point Your target is materially above or below the standard rating, or the shift pattern is unusual Target kg/h, revised envelope and weight, revised power draw and utility demand
Full processing line
Fruit & vegetable sorting, washing, peeling, cutting and drying line
A multi-stage line configuration where washing is one station among sorting, peeling, cutting and drying You are building a complete process rather than adding one washer to an existing room Stage list, throughput match between stages and total footprint — review the line page with the team

What We Need From You to Quote

Five details turn a price range into a real quotation. The PH-6000 is quoted FOB at US$1000–3000 per set with a minimum order of 1 set, and supply ability of 200 sets per month, so the specification conversation moves quickly once these are on the table.

  • Target washed output in kg/h, plus shift pattern and any peaks.
  • Produce list and soil load — leaf, sprouts, cut salad or a mixed daily changeover.
  • Power available at the installation point, measured against the 380V / 1.5 kW standard build.
  • Layout constraints — usable length around a 6000×800×1300 mm body, door widths, conveyor heights and drain position.
  • Destination port and packaging — the page lists Shanghai and Qingdao, and any labelling or packing requirement belongs in the same message.
  • 2000 kg/hPublished capacity of the PH-6000 air-bubble washer.
  • 1 setMinimum order quantity, so a single machine trial order is possible.
  • US$1000–3000 / setIndicative FOB price range listed on the product page.
  • Shanghai & QingdaoPorts listed for shipment.
  • Custom capacityCapacity customization is offered according to production needs.

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

Vegetable Washing Machine Layout for Leaf Vegetable Processing

A leaf vegetable packing plant needs to judge whether a continuous washer fits its floor, utilities, and handoff to sorting and packing before it requests a quotation.

Read article

SUS304 Stainless Steel for Industrial Vegetable Washing Machines

SUS304 is the material baseline for an industrial vegetable washing machine, while approval depends on contact surfaces, cleaning conditions, and a document set agreed before purchase.

Read article

What Does an Air Bubble Cleaning Machine Do in Vegetable Washing?

An air bubble cleaning machine uses rising bubbles, moving water, and spray to lift, separate, and clean leafy vegetables and tender produce as one continuous step. This explanation covers how each…

Read article

Frequently Asked Questions

what produce is the ph-6000 designed to wash?

the product page names leafy and delicate produce, bean sprouts, salad processing lines, fresh produce suppliers, vegetable packaging facilities and ready-to-eat meal production. the bubbling, surfing and spray action is intended to remove dirt and residues while soaking, cleaning and desalting.

how does the air-bubble cleaning system work?

bubbling, surfing and cleaning spray work together, powered by a high-pressure fan and a high-pressure water-impact system. the page describes the result as soaking, cleaning and desalting in one wash stage.

what are the published specifications of the ph-6000?

the published table lists model ph-6000, power 380v and 1.5 kw, net weight 500 kg, capacity 2000 kg/h, overall size 6000×800×1300 mm, and material sus304.

what material is used and how is maintenance handled?

the machine is built in food-grade sus304 stainless steel, described as corrosion- and wear-resistant. the layout is designed for easy cleaning and maintenance to help minimise downtime.

what are the order and shipping details?

the page lists an fob price of us$1000–3000 per set, a minimum order of 1 set, supply ability of 200 sets per month, and shanghai and qingdao as ports. the item number is v002.

can capacity be customized and is installation support available?

capacity customization is offered according to production needs, and the page notes that the machine can integrate with existing processing lines and hygiene systems. installation guidance and remote support are also offered.

Leave a message
Name *
Email *
Phone
Subject
Message *
Verification code *
Click to verify